Adverrun XS Contra Drive System - NO SPINNERS

10e15040-c229-4afb-8dae-fa7343829747
10e15040-c229-4afb-8dae-fa73438297470be29226-0f23-40f1-9f05-a203385eb5ca45f7bbaf-a60f-4a50-af9c-e3158de6e733cf61c971-bcb5-4632-8ec1-85852048a013a3dab6a8-b66f-44c4-aafd-50d6df494a40
This product has NO SPINNERS. Select your spinners from the related products section below. Now included is a Spare Belt and 8mm Main Shaft. We have Falcon contra spinner sets available. This is useful if you need an 89mm spinner diameter (KARAT Bipe). Speak to us if this option is required. This ...Read more
AUD2,080.00 (AUD1,890.91 excl GST) each
No vote


  • Description
  • Specifications
  • Comment
  • Post a comment

This product has NO SPINNERS. Select your spinners from the related products section below.

Now included is a Spare Belt and 8mm Main Shaft.

We have Falcon contra spinner sets available. This is useful if you need an 89mm spinner diameter (KARAT Bipe). Speak to us if this option is required. This option is pictured above with white spinners.

Adverrun is an F3A Contra drive system developed to minimize the torque effects induced by the rotating propeller. Forces which affect the flight path of the plane are reduced in order to focus the pilots attention on performing the maneuvers. Adverrun uses a combined Belt/Gear reduction system to drive two Propellers rotating in opposite directions. It has specifically been designed for F3A use.

The new Adverun XS weight has been significantly reduced compared to the 2016 model. It continues to be largly maintenance free.

Adverrun is offered in combination with the Kontronik Pyro 650 motor. It ships pre-assembled including motor and spinner and comes with screws and rubber mounts. All alloy parts are anodized in Kontronik red. To match your planes nose ring size you can choose from either an 82mm or 85mm spinner (Available separately). Alternatively, Falcon contra spinners can be used with minor modifications to the rear spinner backplate.

Features:

  • Delrin gear and belt drive requires minimal maintenance.
  • Front mount and rear mount. Adverrun is mounted with supplied rubber isolators.
  • Now with soft mount on rear.
  • Rear mount allows for side thrust adjustment with slotted holes. We use 0° side thrust.
  • Motor shaft is supported by front bearing. No extra support is needed for the motor.
  • No special ESC requirements with Pyro 650-53 motor. Can be used with Spin 99 and Mezon ESC’s as well as other F3A controllers.

Technical Data:

Adverrun has been desgined for 10s Lipo packs. We have tested the most common propeller combinations.

  • Front: 22" x 20" / Rear: 22" x 22" (recommended)
  • Front: 22" x 20" / Rear: 22" x 20"
  • Front: 20" x20" / Rear: 20.5" x 20.5"
  • Front: 22" x 18" / Rear: 22" x 20" (can be used - but we found it a bit too slow)
  • Front: 23" x 20" / Rear: 23" x 22" (can be used - but current consumption is quite high)

These combinations will result in maximum currents of 90-120A on the ground providing more power than needed in a typical F3A flight.

Weight has always been a concern in F3A and one of the reasons for the three year Adverrun development phase. Weight very much depends on the motor used. It is common to state weight of contra drives without accessories. We list weight without accessories for comparison with other drives, but also including spinner and accessories (i.e. screws and rubber isolator mounts). Compared to other drives, Adverrun also limits the need for using additional carbon mounting plates to fit the drive in your plane.

  • Adverrun weight: ~585 grams.

 Extra ESC Settings:

  • Timing - 20°
  • Poles - 10
  • Gear Ratio - 4:1
Brand: AdverrunAdverrun
List of the comments:
No comments have been posted yet.
You must have bought this item in order to post a vote or a comment

Related products

Results 1 - 17 of 17

Cart

The cart is empty

Currency Switcher

Latest products